Epoxy.com Product #101
Epoxy Body Coat
Epoxy Slurry and Epoxy Self Leveling Coating (paint)
Description
Epoxy.com Product #101 Epoxy Body Coat is an epoxy coating for
commercial and light industrial floors. Epoxy.com Product #101 Epoxy Body Coat
is designed for slurry and self-leveling epoxy flooring applications. Epoxy.com
Product #101 Epoxy Body Coat helps to smooth seamless epoxy floors that are to
receive Epoxy.com Seamless Epoxy Flooring and Epoxy.com Seamless Epoxy Coating
(paint) systems. Epoxy.com Product #101 Epoxy Body Coat provides an extra
thickness to protect the substrate from chemical attack. Epoxy.com Product #101
Epoxy Body Coat protects the substrate from impact and adds additional abrasion
resistance to Epoxy.com Seamless Epoxy Flooring and Epoxy.com Seamless Epoxy
Coating (paint) systems.
Advantages
- 100% Solids, Zero (0) VOC, means it meets even the strictest low VOC standards
- Cost Effective
- Very Low Odor - Zero (0) VOCs means it meets even the toughest low VOC
standards
- Low Viscosity - means it has excellent wetting and self-leveling
properties
- Can be used to level and smooth floors
- Can be made anti-skid most Epoxy.com Epoxy Anti-Skid Coatings (paints)
or Epoxy.com Anti-Skid Epoxy Flooring System.
Consideration
- Normal Cured Epoxy.com Product #101 requires a minimum temperature of 50° F. to cure. If it will be below 50° F. please contact Epoxy.com for information low temperature cure.
- Substrate must be clean and sound.
- Slight color variation from batch to batch. So typically you will need to seal this with an Epoxy.com Coating
Composition
Epoxy.com Product #101 Epoxy Body Coat is a 100% solids Zero (0) VOC epoxy
resin and epoxy hardener system.
Application
Surface preparation is the first critical step to the installation of a quality seamless flooring system. All substrates to receive Epoxy.com Product #101 Epoxy Body Coat, should be properly prepared.
See Epoxy.com Surface Preparation Guide
for more details
Installation will vary by application. Contact Epoxy.com Technical
Support Department for additional information.
Physical Properties |
| Color | Light Grey, Brick Red, White, & Buff
(other colors by request,
subject to minimum quantity and/or upcharge) |
| Weight/gallon | 10.50-11.0 mixed |
| Solids Content | 100% |
| Mix Ratio | 4A to 1B by volume |
| Pot Life | 45 minutes @ 70° F |
| Viscosity | 1500 cps, mixed approx. |
| VOC | Zero(0) |
Dry Time |
| 10-20 mil Film | 10-14 hours |
| Light Traffic | 16 hours |
| Ultimate Cure @ 74° F | 5 days |
| @50° F | 14 days |
Chemical Resistance |
| |
|
| Reagent |
Rating |
| Acetic Acid 5% |
R |
| Ammonium Hydroxide 10% |
R |
| Citric Acid 5% |
R |
| Coca-Cola Syrup |
R |
| Crude Oil |
R |
| Diesel Fuel |
R |
| Ethylene Glycol |
R |
| Isopropyl Alcohol |
R |
| Ketchup |
R |
| Mineral Oil |
R |
| Sodium Hydroxide 5% |
R |
| Tri-sodium Phosphate 5% |
R |
| Urea 6.6% |
R |
R = continuous service
L = Limited Recommendation, occasional spills |
Performance Properties |
| Tensile Strength ASTM-C-307 | 2,300 psi |
| Smoke Deposited ASTM E-162 | 4 mg. max. |
| Flame Spread ASTM-162 | 25 max. |
| Shrinkage ASTM C-531 | <0.5% |
| Thermal Coefficient of Expansion ASTM C-531 | 17.4 x 10-6 in./in./°F |
| Adhesion - ACI-503R | 300 psi (100% concrete failure Type I) |
| Hardness ASTM-D-2240 | 75 (Shore D) |
| Abrasion, Taber CS-17 ASTM-D-4060 | 0.065 g loss |
| Resistance to Elevated Temperatures | No slip or flow at required temperatures |
| Impact Resistance MTI-D-3134J | Withstands 16ft./lbs. no cracking, delamination or chipping |
| Indentation MIL-D-3134J | Withstands 2,000 lbs./sq.in. for 30 min. without indentation. |
| Heat Deflection Temperature ASTM D-648 | 110°F |
| Moisture Absorption | <1% |
| Flexural Strength ASTM-C-580 | 5,000 psi |
| Compressive Strength ASTM-C-579, 25 Day Cure | 12,000 psi |
|
|
Proper mixing and installation is critical to the optimal success of all products.
See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA
We have products that have passed the test of time as well as the best new Systems available today.
Since 1980 - 40 years of the highest quality products
Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)
Closed for lunch from 12Noon to 1PM
321-206-1833 Customer Service - Ordering and Order Status
Katey Lambert-Fontaine, VP - Chief Operations Officer
sales@epoxy.com
Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
Copyright © 1994-2023 (providing
online information about the right product for the right job for nearly 30 years) EPOXY.COM a
division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
|
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.
|
|