Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Epoxy Wall Coating, 100% Solids High-Build

Thick Bodied Epoxy Coating (Paint) for Verticals and Overhead

Epoxy.com Product #1W (Wall Grade)


EPOXY COATING DESCRIPTION

Product #1W High Build Epoxy Wall Coating - epoxy coating for walls, is a two component, 100% solids epoxy Hi-Build epoxy wall coating used for high indoor traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, tanks, etc.

Epoxy Coating Installation Guide

Epoxy Coatings Calculator

EPOXY COATING ADVANTAGES

  • Moisture Insensitive
  • Ceramic like finish
  • Thicker Bodied Epoxy Makes it an Excellent for Floors and Ceilings
  • Solvent Free
  • Waterproof
  • Extremely Durable
  • Chemical Resistant

SURFACE PREPARATION FOR EPOXY COATING

Epoxy.com Product #1W on the walls of a camp's dog wash area.
Bath House Construction project. Picture compliments of Suwannee River Rendezvous Campground
Epoxy.com Product #1W on Walls
and
Chip Flooring on the floor.

Surfaces  to receive Product #1W High Build Epoxy Wall Coating must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, mechanical abrasion, or acid etching. Remove water and dust from all surfaces with an oil-free blast immediately prior to application.

EPOXY COATING MIXING INSTRUCTIONS

Temperature of Product #1W High Build Epoxy Wall Coating must be 50° F or above at time of mixing. Stir each component separately before blending. Mix 4 parts by volume of Part A with 1 part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.

EPOXY COATING APPLICATION

Apply Product #1W High Build Epoxy Wall Coating with a roller, brush, or spray equipment. Two coats are recommended. Thickness per coat should be 7-10 mils. Seven days cure time is required to reach maximum chemical resistance.

EPOXY COATING LIMITATIONS

DO NOT apply Product #1W High Build Epoxy Wall Coating at temperatures below 50° F. Surface must be dry.

EPOXY COATING SAFETY PRECAUTIONS

Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.

EPOXY CLEAN UP

Clean Product #1W High Build Epoxy Wall Coating from all tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.

EPOXY COATING APPLICATION PROPERTIES @77° F

Mix Ratio 4:1 By Volume
Viscosity (mixed) 2000 -2500 CPS
Pot Life (200 gr.) 40-50 minutes
Tack Free to Touch 8 to 10 Hours
Initial Cure 24 Hours
Final Cure 7 Days
Packaging Unit Size 1.25 gal. unit, 5 gallon unit
Standard Colors White, Light Gray, Dark Gray, Taupe, Sand, Old Gold, Mocha, Brick Red, Slate Blue, Colonial Green, Deep Blue, Black, Safety Yellow

Epoxy.com Epoxy Color Chart HereClick the picture of color card below  for a larger version of this picture of the color chart.
Please note:  The picture to the right is a photographic reproduction of the color card for this product.  The photo reproduction process and your monitor and/or printer will change these colors.  This chart is to give you an idea of the colors available and not intended for critical color selections.

EPOXY TENSILE PROPERTIES

Tensile Strength (ASTM D-638)5500 psi. min.
Elongation4-5%

Other customers who visited this page also visited:

Proper mixing and installation is critical to the optimal success of all products.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA

We have products that have passed the test of time as well as the best new Systems available today.

Since 1980 - 40 years of the highest quality products

Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)

Closed for lunch from 12Noon to 1PM


321-206-1833  Customer Service - Ordering and Order Status
                         Katey Lambert-Fontaine, VP - Chief Operations Officer
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

Copyright © 1994-2023 (providing online information about the right product for the right job for nearly 30 years)  EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.