Epoxy.com Product #661
Vinyl Ester Novolac Binder
DESCRIPTION
Epoxy.com Product VINYL ESTER BINDER is a clear, 100% reactive, vinyl ester novolac used to coat or line concrete or
steel surfaces in chemically aggressive industrial environments. It is used for coating primary and
secondary containment, trenches, troughs, pump pads, and equipment.
ADVANTAGES
- Excellent resistance to a wide range of chemicals.
- High temperature performance; in many cases up to 350°F (spills) or 400°F (dry heat).
- Application by conventional painting techniques.
- Best overall performance coating for secondary containment.
- Self-extinguishing in thin films.
CONSIDERATIONS
- Substrate temperature must be a minimum of 50°F.
- Substrate must be free of dirt, waxes, curing agents, and other foreign materials.
- Substrate must be completely dry.
- Requires skilled installers to assure successful results.
COMPOSITION
Two-component peroxide cured vinyl ester novolac.
APPLICATION
SURFACE PREPARATON
Surface Preparation is the most critical portion of any successful resinous flooring system application. All
substrates must be properly prepared as outlined in
Epoxy.com Surface Preparation Guide
MIXING/APPLICATION
Observe all precautions on MSDS and label when using this product. Mix 3-4 oz. Part B per gallon with
Part A with a low speed drill for at least two (2)minutes. For spray application, add up to 1 quart
Styrene per mixed gallon, if needed.
Apply by roller, brush, or spray. Use a nylon or natural bristle brush or a good quality medium nap roller. Can
be sprayed with airless or conventional spray.
CLEAN UP
Clean skin with soap and water; use MEK, xylene, or clean proprietary epoxy thinners for equipment.
COVERAGE
160 square feet per gallon yields 8 mils DFT due to shrinkage during cure. Two coats are recommended for general service, as a coating.
COLOR SELECTION
Epoxy.com Vinyl Ester Binder is available in Clear.
TECHNICAL DATA
Typical Performance Properties
| Tensile Strength | ASTM D-638 | 11,000 psi |
| Elongation | ASTM D-638 | 2.0-3.0% |
| Adhesion to Metal | ASTM D-638 | 2,500 psi |
| Adhesion to Concrete | ACI COMM #403 | 350 psi (concrete fails) |
| Hardness | ASTM D-2240 | 85 (Shore D) |
| Abrasion Resistance | ASTM 4060 | 26-28 mg. loss (CS-17 wheel,
1 kg load,1000 cycles) |
| Service Temperature | 320°deg;F (immersion) | 400°F (dry heat) |
PHYSICAL PROPERTIES
| Gloss; 60° | High Gloss |
| Weight/Gallon | 8.7 lbs., mixed |
| Solids Content | 100% |
| Mix Ratio | 32A:1B by volume |
| Pot Life | 45 min. @ 75°F (3 gallon kit) |
| Viscosity | 600 cps, mixed approx. |
| Shelf Life | 2 months, maximum |
| Re-Coat | 5-8 hours @ 70°F* |
| Foot Traffic | 8-12 hours |
| Full Chemical | Cure 3-5 days |
| *Shorter recoat times affect gloss. |
CHEMICAL RESISTANCE
REAGENT RATING
|
| Acetic Acid-75% | R |
| Acetone | L |
| Acrylic Acid-25% | R |
| Citric Acid | R |
| Chromic Acid-20% | R |
| Diesel Fuel | R |
| Ethylene Glycol | R |
| Fatty Acids | R |
| Gasoline | R |
| Hydrochloric Acid-37% | R |
| Lactic Acid | R |
| Methyl Ethyl Ketone | L |
| Nitric Acid-30% | R |
| Phenol | L |
| Sodium Hydroxide-50% | R |
| Sulfuric Acid-70% | R |
| Toluene | R |
| Urea | R |
| Vinegar | R |
| Xylene | R |
R-Recommended for continuous service.
L-Limited Recommendation, occasional spills.
*-May cause slight stain or discoloration. |