Pigmented Epoxy Mortar
Epoxy Mortar Binder Resin100% Solids Zero VOC
Epoxy.com Product #24
DESCRIPTION
Pigmented Epoxy Mortar Resin Product #24 is a multipurpose colored epoxy binder for
Epoxy Mortar Systems. This all purpose epoxy resin is characterized as
an excellent general purpose material with good clarity and color retention. It
is essentially odorless and can therefore be used in occupied areas. Pigmented
Epoxy Mortar Resin Product #24 is 100% solids and has Zero (0) VOC, so it meets event the strictest low
VOC standards.
ADVANTAGES
- Good troweling properties
- Excellent color retention
- Low odor for Good troweling properties
- Excellent color retention
CONSIDERATIONS
- Minimum application temperature of 50°F (Contact Epoxy System, Inc.
for Low Temperature Cure)
.
- Substrate must be free of curing agents and any foreign materials.
- Slight color variation can be expected from batch to batch.
- Pigmented version should not be used as a coating.
COMPOSITION
100% solids amine cured Epoxy Resin and Epoxy Hardener.
APPLICATION
SURFACE PREPARATION
Surface Preparation is the most critical portion to any successful resinous flooring system application. All substrates
to receive Pigmented Epoxy Mortar Resin Product #24 must be properly prepared as outlined in
Epoxy Surface
Preparation Procedures. Epoxy.com technical service
department is pleased to answer any questions.
INSTALLATION
Will vary with application method.
PHYSICAL PROPERTIES |
| Color |
Light Grey, Taupe, Sand, Dark Grey, Old Gold, Slate Blue, Mocha,
Colonial Green, Brick Red, Deep Blue, White. Black, Safety Yellow |
| Gloss, 60°F |
85-1 00 |
| Weight/gallon |
9.00-9.5mixed |
| Solids Content |
100% |
| Mix Ratio |
4A to I B by volume |
| Pot Life |
30-40minutes @ 70°F |
| Viscosity |
950 cps, mixed approx. |
| VOC |
0 |
| 10-20 mil film |
10-14 hrs. |
| Light Traffic |
16 hrs. |
| Ultimate Cure @ 74°F |
5 days |
| Dry Time @ 50°F |
14 days |
 Click
the picture of color card below for a larger version of this picture
of the color chart.
Please note: The picture to the right is a photographic reproduction of the
color card for this product. The photo reproduction process and your
monitor and/or printer will change these colors. This chart is to give you
an idea of the colors available and not intended for critical color selections.
CHEMICAL RESISTANCE
R-Recommended for continuous service. L-Limited recommendation, occasional spills.
REAGENT |
RATING |
REAGENT |
RATING |
| Acetic Acid-5% |
L |
Lactic Acid-15% |
R |
| Acetone |
L |
Methyl Ethyl Ketone |
L |
| Bleach |
L |
Nitric Acid-10% |
R |
| Citric Acid-30% |
R |
Skydrol |
R |
| Crude Oil |
R |
Sodium Hydroxide-50% |
R |
| Diesel Fuel |
R |
Sulfuric Acid-20% |
R |
| Ethylene Glycol |
R |
Toluene |
R |
| Fatty Acids |
L |
Urea |
R |
| Gasoline |
R |
Vinegar |
L |
| Hydrochloric Acid-15% |
R |
Xylene |
R |
PERFORMANCE PROPERTIES |
| Tensile Strength ASTM-D-638 |
8500 psi |
| Elongation ASTM-D-638 |
5.5% |
| Adhesion to metal |
2500 psi |
| Adhesion to concrete ACI Committee 403 |
350 psi (concrete fails) |
| Hardness ASTM-D-2240 |
80 (Shore D) |
| Abrasion Resistance ASTM-C-501 |
35-40 mg loss
(CS-17 wheel, 1 kg load, 1000 cycles) |
| Service Temperature MIL- D-3134F |
160 F (immersion)
185 F (dry heat) |
| Impact Resistance MIL-D3134F § 4.7.3 |
Withstands 16ft/lbs.
no cracking, delamination or chipping. |
| Indentation MIL-D-3134F §4.7.4 |
Withstands 2,000 lbs./sq. in. for 30 min.
without indentation. |
Elevated Temperature Resistance
MIL-D-31 34F §4 7 5 |
No slip or flow
at required temperatures at 158°F |
| Water Absorption ASTM-D-670-63 (24. hr. immersion) |
0.10% maximum |
| Flexural Strength ASTM-D-790 |
8,000 psi |
| Compressive Strength ASTM-D-695 |
11,000 psi |
|
|
Proper mixing and installation is critical to the optimal success of all products.
See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA
We have products that have passed the test of time as well as the best new Systems available today.
Since 1980 - 40 years of the highest quality products
Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)
Closed for lunch from 12Noon to 1PM
321-206-1833 Customer Service - Ordering and Order Status
Katey Lambert-Fontaine, VP - Chief Operations Officer
sales@epoxy.com
Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
Copyright © 1994-2023 (providing
online information about the right product for the right job for nearly 30 years) EPOXY.COM a
division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
|
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.
|
|